鸟（Bird）免疫球蛋白M（IgM）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被免疫球蛋白M（IgM）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的免疫球蛋白M（IgM）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、150、300、600、1200、2400μg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于10μg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Bird Immunoglobulin M (IgM) ELISA Kit instruction Intended useThis IgM ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of IgM in the sample, this IgM ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus IgM concentration. The concentration of IgM in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by 0,150,300,600,1200,2400 μg/ml.Reagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 10 μg/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
植物（Plant）果胶甲酯酶（PME）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被果胶甲酯酶（PME）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的果胶甲酯酶（PME）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品活性。样品收集、处理及保存方法1. 样本不能含叠氮钠（NaN3），因为叠氮钠（NaN3）是辣根过氧化物酶（HRP）的抑制剂。2. 标本采集后尽早进行提取，提取按相关文献进行。3. 植物萃取液或其它相关样本：请1000 x g离心20分钟，取上清即可检测。4. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、5、10、20、40、80 U/ml试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 U/ml。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Plant Pectin methylesterases (PME) ELISA Kit instruction Intended useThis PME ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of PME in the sample, this PME ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus PME concentration. The concentration of PME in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storages1. Can’t detect the samples which contain NaN3, because NaN3 inhibits HRP activity of the horseradish peroxidase.2. Extract as soon as possible after Specimen collection, Extracted according to the relevant literature.Cell culture supernates and plant exact fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C) Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by: 0,5,10,20,40,80 U/mlReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 U/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
鸡（Chicken）磷脂酰胆碱（PC）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被磷脂酰胆碱（PC）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的磷脂酰胆碱（PC）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、30、60、120、240、480 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
鸡（Chicken）游离胆固醇（FC）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被游离胆固醇（FC）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的游离胆固醇（FC）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、0.5、1、2、4、8 mmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1 mmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
鸡（Chicken）黄体生成素（LH）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被黄体生成素（LH）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的黄体生成素（LH）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、10、20、40、80、160 ng/ml试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 ng/ml。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Chicken Luteinizing Hormone (LH) ELISA Kit instruction Intended useThis LH ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of LH in the sample, this LH ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus LH concentration. The concentration of LH in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,10,20,40,80,160 ng/mlReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 ng/ml.6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
鸡（Chicken）双氢睾酮（DHT）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被双氢睾酮（DHT）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的双氢睾酮（DHT）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、0.5、1、2、4、8 nmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。 4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1 nmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Chicken Dihydro testosterone (DHT) ELISA Kit instruction Intended useThis DHT ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of DHT in the sample, this DHT ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus DHT concentration. The concentration of DHT in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storagesSerum - Use a serum separator tube and allow samples to clot for 30 minutes before centrifugation for 10 minutes at approximately 3000×g. Remove serum and assay immediately or aliquot and store samples at -20℃ or -80℃.Avoid repeated freeze-thaw cyclesPlasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 30 minutes at 3000×g at 2-8℃ within 30 minutes of collection. Store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Cell culture supernates and other biological fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20℃or -80℃. Avoid repeated freeze-thaw cycles.Note: The samples shoule be centrifugated dequately and no hemolysis or granule was allowed.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C)Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by:0,0.5,1,2,4,8 nmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 0.1 nmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
鸡（Chicken）睾酮（T）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被睾酮（T）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的睾酮（T）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 血清：使用不含热原和内毒素的试管，操作过程中避免任何细胞刺激，收集血液后，3000转离心10分钟将血清和红细胞迅速小心地分离。2. 血浆：EDTA、柠檬酸盐或肝素抗凝。3000转离心30分钟取上清。3. 细胞上清液：3000转离心10分钟去除颗粒和聚合物。4. 组织匀浆：将组织加入适量生理盐水捣碎。3000转离心10分钟取上清。5. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白，按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、17.5、35、70、150、300 pg/mL试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 待测样本孔先加样本10μL，再加样本稀释液40μL(即样本稀释5倍)；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 pg/mL。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。
盐酸克伦特罗检测豪运国际（酶联免疫法） 产品货号：DM-S4156 1 原理及用途本豪运国际采用间接竞争ELISA方法检测尿样、组织、饲料等样本中的盐酸克伦特罗（Clenbuterol，CLE），豪运国际由预包被偶联抗原的酶标板、辣根酶标记物、抗体、标准品及其他配套试剂组成。检测时，加入标准品或样本溶液，样本中的盐酸克伦特罗和酶标板上预包被偶联抗原竞争抗盐酸克伦特罗抗体，加入酶标记物后，用TMB底物显色，样本吸光度值与其所含盐酸克伦特罗含量成负相关，与标准曲线比较即可得出样本中盐酸克伦特罗的残留量。2 技术指标2.1 豪运国际灵敏度：0.05ppb(ng/ml)2.2 反应模式：25℃，30min～15min2.3 检测下限：尿样……………………………0.1ppb组织……………………………0.2ppb饲料……………………………1ppb猪肝……………………………0.5ppb2.4 交叉反应率：克伦特罗………………………100%特普他林………………………<1%马布特罗………………………<1%溴布特罗………………………<1%沙丁胺醇………………………<1%莱克多巴胺……………………<1% 2.5 样本回收率：尿样……………………………95%±10%组织、饲料、猪肝……………85%±15%3 豪运国际组成酶标板……………………………96孔标准液：各1ml0ppb、0.05ppb、0.15ppb、0.45ppb、1.35ppb、4.05ppb高标准液（红盖）：100ppb………1ml酶标记物（红盖）…………………5.5ml抗体工作液（蓝盖）………………5.5ml底物液A（白盖）……………………6ml底物液B（黑盖）……………………6ml终止液（黄盖）………………………6ml20×浓缩洗涤液（白盖）……………40ml10×复溶液(黄盖) …………………50ml说明书…………………………………1份盖板膜…………………………………1张自封袋…………………………………1个4 需要的器材和试剂4.1 仪器：酶标仪、打印机、均质器、氮气吹干装置、振荡器、离心机、刻度移液管、天平（感量0.01g）4.2 微量移液器：单道20µl-200µl，100µl-1000µl、多道300µl4.3 试剂：氢氧化钠、乙酸乙酯、浓盐酸、甲醇、无水碳酸钠 5 样本前处理5.1 样本处理前须知：实验器具必须洁净并使用一次性吸头，以避免污染干扰实验结果。5.2 配液：配液1：复溶液将10×复溶液用去离子水10倍稀释（1份10×复溶液加9份去离子水），用于样本的复溶，复溶液在4℃环境可保存一个月。配液2：工作洗涤液将20×浓缩洗涤液20倍稀释(1份20×浓缩洗涤液加19份去离子水)。配液3：样本提取液70%甲醇，即V甲醇:V去离子水=7：3。配液4：10%碳酸钠溶液 取50g无水碳酸钠加去离子水混匀溶解，定容至450ml。配液5：0.1M盐酸溶液 称取860ul浓盐酸加去离子水混匀，定容至100ml。配液6：2M氢氧化钠溶液 称取8g氢氧化钠加去离子水混匀溶解，定容至100ml。5.3 样本前处理步骤：5.3.1 尿样处理方法： 取1ml清亮尿样（浑浊尿样需要过滤或经4000r/min离心5min以得到清亮尿样）于10ml离心管中，加入1ml复溶液（配液1），混合振荡30s，取50µl进行分析。暂不使用的样本应冷冻保存。样本稀释倍数：2 检测下限：0.1ppb5.3.2 组织样本处理方法： 称取均质后的组织样本1g±0.05g，加入3ml复溶液（配液1），充分振荡2min，室温4000r/min以上离心10min (若组织样本中油脂含量较高，可在振荡后放入85℃水浴10min后再离心)。取50µl上清液进行分析。样本稀释倍数：4 检测下限：0.2ppb5.3.3 饲料样本处理方法：1）称取粉碎后的饲料样本1g±0.05g于15ml离心管中，加入4ml样本提取液(配液3)，振荡混匀2min，室温 4000r/min以上离心10min；2）取上清液0.1ml于1.5ml离心管中，再加入0.4ml复溶液(配液1)，振荡混匀30s，取50ul分析。样本稀释倍数：20 检测下限：1ppb5.3.4猪肝样本处理办法1)称取均质后的猪肝样本1g±0.05g于15ml离心管中，加入1ml 10%碳酸钠溶液（配液4）,振荡混匀2min，加入4ml乙酸乙酯溶液，振荡混匀5min，室温4000r/min以上离心10min；2）取上层有机液2ml于15ml离心管中，加入1ml 0.1M盐酸溶液（配液5），振荡混匀2min，室温4000r/min以上离心5min；3）取下层清液0.1ml于1.5ml离心管中，加入0.4ml复溶液（配液1），用2M 氢氧化钠溶液（配液6）调PH至 7 左右，取50ul分析。 样本稀释倍数：10 检测下限：0.5ppb6 酶联免疫试验步骤 将所需试剂从4℃冷藏环境中取出，置于室温平衡30min以上, 洗涤液冷藏时可能会有结晶需恢复到室温以充分溶解，每种液体试剂使用前均须摇匀。取出需要数量的微孔板及框架，将不用的微孔板放入自封袋，保存于2-8℃。6.1 编 号：将样本和标准品对应微孔按序编号，每个样本和标准品做2孔平行，并记录标准孔和样本孔所在的位置。6.2 加样反应：加标准品或样本50µl/孔到各自的微孔中，然后加酶标记物50µl/孔，再加入50µl/孔的抗体工作液，用盖板膜封板，轻轻振荡5秒混匀，25℃反应30分钟。6.3 洗 涤：小心揭开盖板膜，甩去孔内液体，每孔加350ul工作洗涤液，静置30秒后弃去，重复洗涤5次，＊后一次拍干（用吸水纸拍干，拍干后未被清除的气泡可用干净的枪头刺破）。6.4 显 色：每孔加入底物液A 50µl，再加底物液B 50µl，轻轻振荡5秒混匀，25℃避光显色15分钟（若蓝色过浅，可适当延长反应时间）。 6.5 终 止：每孔加入终止液50µl，轻轻振荡混匀，终止反应。6.6 测吸光值：用酶标仪于450nm处测定每孔吸光度值（建议用双波长450/630nm）。测定应在终止反应后10分钟内完成。7 结果分析7.1 百分吸光率的计算 标准液或样本的百分吸光率等于标准液或样本的百分吸光度值的平均值（双孔）除以第一个标准液（0ppb）的吸光度值，再乘以100%，即 百分吸光度值（%）＝A×100%A0A—标准溶液或样本溶液的平均吸光度值A0—0ppb标准溶液的平均吸光度值7.2 标准曲线的绘制与计算 以标准液百分吸光率为纵坐标，对应的标准液浓度（ppb）的对数为横坐标，绘制标准液的半对数曲线图。将样本的百分吸光率代入标准曲线中，从标准曲线上读出样本所对应的浓度，乘以其对应的稀释倍数即为样本中待测物的实际浓度。 若利用豪运国际专业分析软件进行计算，更便于大量样本的准确、快速分析。（欢迎来电索取）8 注意事项8.1 室温低于25℃或试剂及样本没有回到室温（25℃）会导致所有标准的OD值偏低。8.2 在洗板过程中如果出现板孔干燥的情况，则会出现标准曲线不成线性，重复性不好的现象。所以洗板拍干后应立即进行下一步操作。8.3 混合要均匀，洗板要彻底，在ELISA分析中的再现性，很大程度上取决于洗板的一致性。8.4 在所有孵育过程中，用盖板膜封住微孔板，避免光线照射。8.5 不要使用过了有效期的豪运国际，不要交换使用不同批号豪运国际中的试剂。8.6 显色液若有任何颜色表明变质，应当弃之。0标准的吸光度值小于0.5个单位（A450nm< 0.5 ）时，表示试剂可能变质。8.7 反应终止液有腐蚀性，避免接触皮肤。9 贮藏及保存期储藏条件：豪运国际于2-8℃保存，避免冷冻。保 质 期：该产品有效期为1年，生产日期见包装盒。
植物（Plant）抗坏血酸（AsA）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被抗坏血酸（AsA）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的抗坏血酸（AsA）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 样本不能含叠氮钠（NaN3），因为叠氮钠（NaN3）是辣根过氧化物酶（HRP）的抑制剂。2. 标本采集后尽早进行提取，提取按相关文献进行。3. 植物萃取液或其它相关样本：请1000 x g离心20分钟，取上清即可检测。4. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、5、10、20、40、80μmol/L试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于0.1μmol/L。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Plant Ascorbic acid (AsA) ELISA Kit instruction Intended useThis AsA ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of AsA in the sample, this AsA ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus AsA concentration. The concentration of AsA in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storages1. Can’t detect the samples which contain NaN3, because NaN3 inhibits HRP activity of the horseradish peroxidase.2. Extract as soon as possible after Specimen collection, Extracted according to the relevant literature.Cell culture supernates and plant exact fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C) Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by: 0,5,10,20,40,80 μmol/LReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 0.1 μmol/L6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
植物（Plant）还原型谷胱甘肽（GSH）ELISA检测豪运国际本豪运国际只能用于科学研究，不得用于医学诊断检测原理豪运国际采用双抗体一步夹心法酶联免疫吸附试验（ELISA）。往预先包被还原型谷胱甘肽（GSH）抗体的包被微孔中，依次加入标本、标准品、HRP标记的检测抗体，经过温育并彻底洗涤。用底物TMB显色，TMB在过氧化物酶的催化下转化成蓝色，并在酸的作用下转化成＊终的黄色。颜色的深浅和样品中的还原型谷胱甘肽（GSH）呈正相关。用酶标仪在450nm 波长下测定吸光度（OD 值），计算样品浓度。样品收集、处理及保存方法1. 样本不能含叠氮钠（NaN3），因为叠氮钠（NaN3）是辣根过氧化物酶（HRP）的抑制剂。2. 标本采集后尽早进行提取，提取按相关文献进行。3. 植物萃取液或其它相关样本：请1000 x g离心20分钟，取上清即可检测。4. 保存：如果样本收集后不及时检测，请按一次用量分装，冻存于-20℃，避免反复冻融，在室温下解冻并确保样品均匀地充分解冻。自备物品1. 酶标仪（450nm）2. 高精度加样器及枪头：0.5-10uL、2-20uL、20-200uL、200-1000uL3. 37℃恒温箱操作注意事项1. 豪运国际保存在2-8℃，使用前室温平衡20分钟。从冰箱取出的浓缩洗涤液会有结晶，这属于正常现象，水浴加热使结晶完全溶解后再使用。2. 实验中不用的板条应立即放回自封袋中，密封（低温干燥）保存。3. 浓度为0的S0号标准品即可视为阴性对照或者空白；按照说明书操作时样本已经稀释5倍，＊终结果乘以5才是样本实际浓度。4. 严格按照说明书中标明的时间、加液量及顺序进行温育操作。5. 所有液体组分使用前充分摇匀。豪运国际组成名称96孔配置48孔配置备注微孔酶标板12孔×8条12孔×4条无标准品0.3mL*6管0.3mL*6管无样本稀释液6mL3mL无检测抗体-HRP10mL5mL无20×洗涤缓冲液25mL15mL按说明书进行稀释底物A6mL3mL无底物B6mL3mL无终止液6mL3mL无封板膜2张2张无说明书1份1份无自封袋1个1个无注：标准品（S0-S5）浓度依次为：0、5、10、20、40、80 ng/ml试剂的准备 20×洗涤缓冲液的稀释：蒸馏水按1：20稀释，即1份的20×洗涤缓冲液加19份的蒸馏水。洗板方法1. 手工洗板：甩尽孔内液体，每孔加满洗涤液，静置1min后甩尽孔内液体，在吸水纸上拍干，如此洗板5次。2. 自动洗板机：每孔注入洗液350μL，浸泡1min，洗板5次。操作步骤1. 从室温平衡20min后的铝箔袋中取出所需板条，剩余板条用自封袋密封放回4℃。2. 设置标准品孔和样本孔，标准品孔各加不同浓度的标准品50μL；3. 样本孔先加待测样本10μL，再加样本稀释液40μL；空白孔不加。4. 除空白孔外，标准品孔和样本孔中每孔加入辣根过氧化物酶（HRP）标记的检测抗体100μL，用封板膜封住反应孔，37℃水浴锅或恒温箱温育60min。5. 弃去液体，吸水纸上拍干，每孔加满洗涤液，静置1min，甩去洗涤液，吸水纸上拍干，如此重复洗板5次（也可用洗板机洗板）。6. 每孔加入底物A、B各50μL，37℃避光孵育15min。7. 每孔加入终止液50μL，15min内，在450nm波长处测定各孔的OD值。结果判断 绘制标准曲线：在Excel工作表中，以标准品浓度作横坐标，对应OD值作纵坐标，绘制出标准品线性回归曲线，按曲线方程计算各样本浓度值。 豪运国际性能1. 准确性：标准品线性回归与预期浓度相关系数R值，大于等于0.9900。2. 灵敏度：＊低检测浓度小于1.0 ng/ml。3. 特异性：不与其它可溶性结构类似物交叉反应。4. 重复性：板内、板间变异系数均小于15%。5. 贮藏：2-8℃，避光防潮保存。6. 有效期：6个月免责声明1. 豪运国际仅供研究使用，不得用于临床实验或人体实验，否则所产生的一切后果，由实验者承担，本公司概不负责。2. 严格按照说明书操作，实验者违反说明书操作，后果由实验者承担。 FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. Plant reduced glutathione (GSH) ELISA Kit instruction Intended useThis GSH ELISA kit is intended Laboratory for Research use only and is not for use in diagnostic or therapeutic procedures.The Stop Solution changes the color from blue to yellow and the intensity of the color is measured at 450 nm using a spectrophotometer. In order to measure the concentration of GSH in the sample, this GSH ELISA Kit includes a set of calibration standards. The calibration standards are assayed at the same time as the samples and allow the operator to produce a standard curve of Optical Density versus GSH concentration. The concentration of GSH in the samples is then determined by comparing the O.D. of the samples to the standard curve.Sample collection and storages1. Can’t detect the samples which contain NaN3, because NaN3 inhibits HRP activity of the horseradish peroxidase.2. Extract as soon as possible after Specimen collection, Extracted according to the relevant literature.Cell culture supernates and plant exact fluids - Remove particulates by centrifugation and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw.Materials required but not supplied1. Standard microplate reader(450nm)2. Precision pipettes and Disposable pipette tips.3. 37 ℃ incubatorPrecautions1. Do not substitute reagents from one kit to another. Standard, conjugate and microplates are matched for optimal performance. Use only the reagents supplied by manufacturer.2. Do not remove microplate from the storage bag until needed. Unused strips should be stored at 2-8°C in their pouch with the desiccant provided.3. Mix all reagents before using.Remove all kit reagents from refrigerator and allow them to reach room temperature ( 20-25°C) Materials suppliedName96 determinations48 determinationsMicroelisa stripplate12*8strips12*4stripsStandard0.3ml*6tubes0.3ml*6tubesSample Diluent6.0ml3.0mlHRP-Conjugate reagent10.0ml5.0ml20X Wash solution25ml15mlChromogen Solution A6.0ml3.0mlChromogen Solution B6.0ml3.0mlStop Solution6.0ml3.0mlClosure plate membrane22User manual11Sealed bags11Note: Standard (S0 → S5) concentration was followed by: 0,5,10,20,40,80 ng/mlReagent preparation20×wash solution:Dilute with Distilled or deionized water 1:20.Assay procedure1. Prepare all reagents before starting assay procedure. It is recommended that all Standards and Samples be added in duplicate to the Microelisa Stripplate.2. Add standard: Set Standard wells, testing sample wells. Add standard 50μl to standard well.3. Add Sample: Add testing sample 10μl then add Sample Diluent 40μl to testing sample well; Blank well doesn’t add anyting.4. Add 100μl of HRP-conjugate reagent to each well, cover with an adhesive strip and incubate for 60 minutes at 37°C. 5. Aspirate each well and wash, repeating the process four times for a total of five washes. Wash by filling each well with Wash Solution (400μl) using a squirt bottle, manifold dispenser or autowasher. Complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting. Invert the plate and blot it against clean paper towels.6. Add chromogen solution A 50μl and chromogen solution B 50μl to each well. Gently mix and incubate for 15 minutes at 37°C. Protect from light.7. Add 50μl Stop Solution to each well. The color in the wells should change from blue to yellow. If the color in the wells is green or the color change does not appear uniform, gently tap the plate to ensure thorough mixing.8. Read the Optical Density (O.D.) at 450 nm using a microtiter plate reader within 15 minutes.Calculation of results1. This standard curve is used to determine the amount in an unknown sample. The standard curve is generated by plotting the average O.D. (450 nm) obtained for each of the six standard concentrations on the vertical (Y) axis versus the corresponding concentration on the horizontal (X) axis. 2. First, calculate the mean O.D. value for each standard and sample. All O.D. values, are subtracted by the mean value of the zero standard before result interpretation. Construct the standard curve using graph paper or statistical software. 3. To determine the amount in each sample, first locate the O.D. value on the Y-axis and extend a horizontal line to the standard curve. At the point of intersection, draw a vertical line to the X-axis and read the corresponding concentration. 4. Any variation in operator, pipetting and washing technique, incubation time or temperature, and kit age can cause variation in result. Each user should obtain their own standard curve.5. The sensitivity by this assay is 1.0 ng/ml6. Standard curve Storage： 2-8℃.validity： six months. FOR RESEARCH USE ONLY; NOT FOR THERAPEUTIC OR DIAGNOSTIC APPLICATIONS! PLEASE READ THROUGH ENTIRE PROCEDURE BEFORE BEGINNING!
31011502012822